OKI C530 Color-Laserdrucker
ERROR 002 = CPU Exception
ERROR 003 = CPU Exception
ERROR 004 = CPU Exception
ERROR 005 = CPU Exception
ERROR 006 = CPU Exception
ERROR 007 = CPU Exception
ERROR 008 = CPU Exception
ERROR 009 = CPU Exception
ERROR 010 = CPU Exception
ERROR 011 = CPU Exception
ERROR 020 = CU ROM Hash Check Error
ERROR 024 = CU ROM Hash Check Error
ERROR 025 = Kanji Font Error
ERROR 030 = CU RAM Check Error
ERROR 031 = CU RAM Check Error
ERROR 036 = CU optio l RAM check error
ERROR 040 = CU EEPROM error
ERROR 041 = CU flash memory error or CU board flash ROM error
ERROR 042 =
ERROR 043 =
ERROR 045 = Flash memory file system error
ERROR 052 = Image processor driver error
ERROR 067 =
ERROR 068 = Interface monitor error
ERROR 070 = PostScript error
072 ERROR xx = Engine interface error or PU-CU interface error
073 ERROR = Video error. An error was detected in expanding image data (an invalid data was received)
074 ERROR xxxx =
075 ERROR xxxx = Video error. An error was detected in expanding image data.
ERROR 081 = Parameter matching check error, Reading from or writing into EEPROM or flash memory cannot be made properly.
ERROR 104 = An engine EEPROM read/write error was detected.
ERROR 106 = Engine control logic error
ERROR 112 = The 2nd tray for a model different from the printer was detected.
ERROR 121 = High-voltage power supply interface error
ERROR 122 = Rear-fan error
ERROR 123 = Ambient humidity error or non connection of humidity sensor
ERROR 124 = Ambient temperature error
128 ERROR 05 = Image drum fan error
128 ERROR 08 = Front fan error
ERROR 131 = LED head detection error (131 = Y)
ERROR 132 = LED head detection error (132 = M)
ERROR 133 = LED head detection error (133 = C)
ERROR 134 = LED head detection error (134 = K)
ERROR 142 = Image drum up-down movement position detection error
ERROR 153 = Image drum unit fuse-cut error
ERROR 154 = Belt unit fusecut error
ERROR 155 = Fuser unit fuse-cut error
ERROR 160 = Toner sensor detection error (160 = Y)
ERROR 161 = Toner sensor detection error (161 = M)
ERROR 162 = Toner sensor detection error (162 = C)
ERROR 163 = Toner sensor detection error (163 = K), This error does not occur with the printer in the factory shipped configuration.
ERROR 167 = Thermistor slope error
ERROR 168 = Compensation thermistor error
ERROR 171 = A fuser thermistor short or open circuit was detected.
ERROR 172 =
ERROR 173 = A fuser thermistor temperature error (high or low temperature) was detected.
ERROR 174 = A backup thermistor shot circuit was detected (high temperature)
ERROR 175 = A backup thermistor open circuit was detected (low temperature)
ERROR 176 =
ERROR 177 = A backup thermistor temperature error (high or low temperature) was detected.
ERROR 182 = Option unit interface error
ERROR 190 = System memory overflow
ERROR 202 = PU firmware download error
ERROR 203 = CU program error
ERROR 204 = CU program error
ERROR 207 = CU program error
ERROR 208 = CU program error
DOWNLOAD ERROR 209 = Custom Media Type table downloading failure, Custom Media Type table downloading failed.
ERROR 213 = CU program error
ERROR 214 = CU program error
FFF ERROR = CU program error (203 to 214 do not occur in general use of the printer), Invalid processing was performed
with a CU program.
ERROR 231 = TAG interface error, A TAG interface error was detected. 01: A short-circuit error. 02: TAG communication error.
ERROR 250 = SD card error
ERROR 251 = SD card erasure error
ERROR 252 = SD card error
ERROR 255 = SD card security error
ERROR 256 = SD card error
ERROR 257 = SD card error
ERROR 901 = Short circuit, Belt temperature error
ERROR 902 = Open circuit, Belt temperature error
ERROR 903 = High temperature, Belt temperature error
ERROR 904 = Low temperature, Belt temperature error
ERROR 923 = A lock error with black image drum
ERROR 928 = Fuser motor lock error
ERROR 933 = Tray-2 CPU clock frequency error
ERROR 980 = Duplicate toner cartridge detection error, Multiple toner cartridges for the same color ware detected.
ERROR 983 = Duplicate toner cartridge detection error, Multiple toner cartridges for the same color ware detected.
ERROR 990 = Waste toner sensor detection error
CRC CHECK NG = PU download data CRC check error, A CRC check error was detected after downloading of PU data
PU firmware and custom media data).
WDT ERROR ADR = XXXX = PU firmware ru way
COMMUNICATION ERROR = PU-CU interface error