Bail
C2858-60115 Bail assembly - Has star wheel assemblies attached
Bail Lift Mechanism
C2858-60209 Bail Lift Mechanism Kit - Includes Cam Gear, Engaging Lever, Engaging Lever Gear, Engaging Lever Spring, Y-Tensioner Bracket, Bail Lift Cam, Cam Gear Support, Screws, Washers
Belt, Zahnriemen, Antriebsriemen
1500-0855 'Y' Axis Belt - from Carriage Motor to Reduction Pulley
1500-0856 Carriage belt
Bin
C1633-00019 Media bin back - For top of wire rack below plotter
C1633-00020 Media Bin Front - Main Part of Wire Rack Below Plotter
C1633-00044 Media Bin Adjust - Adjustable Media Bottom Stop in Wire Rack
Blade See Description Cutter Assembly Blades NOT Separately Available Order Cutter
Bracket
C1633-40037 Bail Bracket - Located on Right End of Bail
C1633-40038 Bail Bracket - Located on Left End of Bail
C2847-00051 Y-Tensioner Bracket - Installed on Left Side Plate - (P/O the Bail Lift Mechanism Kit)
Brake/Housing
C4704-60199 Brake/housing assembly (on right side) - Accepts the flange end of the spindle rod assembly - Includes the 2 housing pieces, 2 brake shoes, brake gear, brake lever, and springs
Bushing
C1633-40082 Bushing - Retains Spring on Shaft of Pincharm Assembly
Cable, Kabel
C1633-60050 Trailing Cable - from Main Logic Board to Carriage Assembly
C2847-60019 Ribbon Cable - from Main Logic Bd to 'X' Encoder (on Motor)
C2847-60034 Ribbon Cable - from Main Logic Board to (Ink) Drop Sense Bd
Cam
C1633-40052 Bail Lift Cam - Activates the Bail Lift Lever (P/O the Bail Lift Mechanism Kit)
Carriage, Schlitten, Patronen Wagen
C1633-60120 Carriage Assy - Includes Carriage PC Board - Can Be Used on any Plotter Regardless of Version of Firmware ROMS
C2847-60071 Carriage Assy - Includes Carriage PC Board - Can be Used on Any Plotter That Has Firmware ROMS of Version 3.3 - WARNING DAMAGE CAN OCCUR IF FIRMWARE VERSION IS NOT 3.3. Plotters with Serial Prefix xxxxAyyyyy, USxxxxxxxx, or <&= esc4806556 may need to upgrade firmware to version 3.3 & install new carriage(c2847-60071)if having print problems
Caster
1492-0145 Lockable Caster Assembly - Includes Stem and Washer (4 Used)
Cleaning Supplies
C6247A DesignJet cleaning kit - Includes cleaning solution and 20 cleaning rags
Clip
C1633-40092 Starwheel Clip - Holds Starwheel on Starguard Bar (9 Used)
Control Panel, Bedienfeld
C2847-60087 Control panel assembly - Includes ribbon cable
Cover
C1633-40047 Right end cover - For end of upper stand (Chassis) assembly
C2847-60062 Left end cover assembly - For end of upper stand (Chassis)
C4706-60084 Rollfeed access cover - Opens forward to allow access to paper spindle assembly - Includes cover and springs
Cross-Brace
C3186-00034 Cross-brace - Main structure that extends between stand legs
Cutter, Messer
C2858-60021 Cutter mechanism assembly - Auto cutter for rollfeed paper
End Cap, Spindel
C2858-40043 Spindle End Cap (Small) (or Core Spacer) - on the Left End of the Spindle Rod - Removes for Loading the Media Roll
C3172-40006 Spindle End Cap (Large) - on Right End of the Spindle Rod
Fan, Lüfter
3160-0814 12V DC Fan - in Electronics Enclosure Assembly
Gear, Zahnrad
C1633-40019 Cluster Gear - Mounts to the Left Side Plate of the Plotter - Between the Paper Drive Roller Gear and the Overdrive Gear
C1633-40027 Bail Engaging Lever Gear - Small Gear Mounted on the Support for the Bail Lift Cam Gear and the Bail Lift Engaging Gear (P/O the Bail Lift Mechanism Kit)
C1633-40028 Bail Lift Cam Gear - Large Gear Mounted on the Support for the Bail Lift Cam Gear and the Bail Lift Engaging Gear (P/O the Bail Lift Mechanism Kit)
Gear Assembly
C4705-60089 Clutch / Overdrive Gear Assembly - Mounts Above the Cluster Gear on the Left Side Plate of the Plotter - Includes Gear, Clutch, Retaining Clip and Two Washers
Handle, Papier Hebel
C1633-40030 Pinchwheel manual lift handle - Paper loading lever
Hardware Kit
C2847-60061 Hardware kit - Package of 6 screws for stand assembly
Hinge
07575-40012 Male Half of Hinge (on Window) - for Lift-Up Window
07575-40111 Female Half of Hinge (on Chassis) - for Lift-Up Window
Holder
C1633-40094 Holder - For 'Help' card and hand held cutter
Housing
C4704-60082 Housing Assembly (on Left Side) - Accepts the Left Side (End with Smaller End Cap) of the Paper Spindle Assembly Kit,
Wartungs Kit
5182-7318 Maintenance Kit - Includes Carriage Assy, Reduction Pulley, 'Y' Belt, Ink Drop Sense Board, Small End Cap for Paper Spindle, Wiper Pad, and a Service Station Kit
C2847-60083 Service Station Kit - Includes Sled, Fitting Caps and Service Station Caps
Label
C3195-00057 Safety Label - Provides Warning that Encoder Strip is Sharp Should be Placed so it is Visible when Top Cover is Open
Leg
C2848-60002 Leg Assembly - Side Support with Foot Bar and 2 Casters (2 Used)
Lever
C2847-40013 Bail Engaging Lever - Used to Move Engaging Lever Gear (P/O the Bail Lift Mechanism Kit)
Memory (Product)
C2065A 4MB SIMM Memory Module Upgrade - 80nS, 36 Bit (One SIMM)
C2066A 8MB SIMM Memory Module Upgrade - 80nS, 36 Bit (One SIMM)
Memory (SIMM)
D2152-69001 8MB SIMM Memory Module - 80nS, 36 Bit (C2066A) REQUIRES RETURN OF DEFECTIVE PART(New part = D2152-63001)
D2156-69001 4MB SIMM Memory Module - 80nS, 36 Bit (C2065A) REQUIRES RETURN OF DEFECTIVE PART(New part = D2156-63001)
Motor
3140-0854 Stepper Motor - for 'Service Station' Drive
C2847-60221 Motor Assy - 'Y' Axis Drive (Carriage) - with Power Cable
Motor/Gear
C2848-60003 Motor/Encoder Assy (Includes Helical Drive Gear) - 'X' Axis Drive - NOTE: Motor and Gear are Only Sold as a Set
Nameplate/Logo
C2847-00038 nameplate - on Left Endcover
Overdrive Assy
C4706-60121 Overdrive Support Assembly - Mounts Between the Left and Right Side Plates of the Plotter
PC Board, Netzteil, Mainboard
0950-2417 Power supply board
C1633-68103M (Ink) Drop Sense Board - Located in Service Station Assembly
C1633-68105M Interconnect Board - in Electronics Enclosure Assembly
C2847-69101 Main logic board REQUIRES RETURN OF DEFECTIVE PART(New part = C2847-68101)
See Description Carriage PC Board - NOT Sold Separately - Order Carriage Asy
Pincharm
C1633-60039 Pincharm Assembly - Curved Black Plastic Plate with 4 Small Rubber Rollers (Does NOT Include Spring or Bushing) (4 Used)
Plate
C2847-00027 SIMM Plate - Covers access to SIMM slot connectors
Power Module, Netzteil
0950-2372 Power supply module - 100-240VAC input, 47-63Hz, requires separate AC power cord - 5VDC output, 1A, 5 watts - For J2382/83A/B
0950-3169 Power supply module - 110-127V AC 57-63Hz input - 13V DC output at 300mA - For the USA and Ca da - For use with the J2592A exter l JetDirect LAN interface module
0950-3170 Power supply module - 209-253VAC input, 47-53Hz - 13VDC output, 300mA - For Europe and Israel - For J2592A
0950-3349 Power Module - for JetDirect Modules and Infrared Interface Models J2590/91/93/94A, J2964A, J3258A/B, J3263/64/65A, J3282B, J4101A/B, J4102A/B - 230V in Europe/Israel
Pulley, Umlenkrolle
07570-60105 Idler Pulley - for Main Drive Belt - on Left End of Plotter
07570-60112 Idler Drive Pulley - Applies Tension to the Pen Carriage Drive Belt (Small Belt) - on Right End of Plotter
C3170-60009 Reduction Pulley - Between the Motor Belt and Carriage Belt
Roller
C2859-60004 Paper Drive (Platen) Roller Assy - Long Gear Driven Roller
Sensor
C2847-60021 Media Sensor Assy - Includes Cable - on Right Side of Platen
C2847-60022 Pincharm Sensor - on Right End of Chassis - Includes Cable
C2847-60069 Sensor Assembly (for Lift-Up Window) - under Right Endcover
C3180-60034 Pincharm Sensor - on Right End of Chassis - Includes Cable
Shield
C4704-40050 SIMM Module Shield (Barrier) - Protective Metal Rectangular Housing - Surrounds SIMM Slots on the Main Logic Board
Spindle Kit, Achse für Rollen Papier
C2848-60011 Rollfeed Spindle Rod Assembly - Includes Spindle and End Caps
C3173A E/A0 Rollfeed Spindle Rod Assembly - Includes Spindle and End Caps
Starwheel
C1633-60051 Starwheel Assembly (Small Plastic Wheel with Metal Teeth) - Mounts on Starguard Bar (9 Used)
Starwheel Mount
C4713-60035 Starwheel Mount Assembly (13 Used) - Includes: Cover, Body, Spring and Two Starwheels - Mounts on the Bail Assembly (Note: Part Number is for One Starwheel Mount Assembly ONLY)
Strip, Encoder
C4714-60098 Encoder Strip Assembly - Connects from Left to Right Side of Plotter - Includes Encoder Strip and Encoder Strip Spring
Support
C2847-40015 Cam Gear Support - Supports Bail Lift Cam Gear - Mounted on Y-Tensioner Bracket (P/O the Bail Lift Mechanism Kit)
Switch, schalter
C2847-60044 Power switch assembly - Includes cable
Wedge, Umlenk Mechanik
07550-40104 Tensioning Wedge - for the Pen Carriage Drive Belt Pulley - (Mounts on the Right Side of the Chassis)
Window
C1633-40075 Lift-Up Viewing Window - on Top of Chassis
Wiper
C1633-40006 Wiper Pad - Part of Wiper Assembly
C3180-60014 Wiper Assy - Left Side of Plotter - Part of Service Station - Includes Wiper Rocker, Wiper Rod and Wiper Pad
HP DesignJet 600 C2848A Plotter Ersatzteile