C3191-60095 Bail Assembly - Includes Bail, Starwheels, and Brackets

Bail Lift Mechanism
C2858-60209 Bail Lift Mechanism Kit - Includes Cam Gear, Engaging Lever, Engaging Lever Gear, Engaging Lever Spring, Y-Tensioner Bracket, Bail Lift Cam, Cam Gear Support, Screws, Washers

Belt, Zahnriemen, Antriebsriemen
1500-0855 'Y' Axis Belt - from Carriage Motor to Reduction Pulley
1500-0856 Carriage belt

C3180-40014 Front panel bezel - Mounts over front panel

C1633-00019 Media bin back - For top of wire rack below plotter
C1633-00020 Media Bin Front - Main Part of Wire Rack Below Plotter
C1633-00044 Media Bin Adjust - Adjustable Media Bottom Stop in Wire Rack

07575-40125 Drive-Tensioner Bracket - Holds Pen Carriage Drive Belt Tensioning Wedge
C1633-00132 Encoder Spring Bracket - Installed on Right Side of Plotter
C1633-40037 Bail Bracket - Located on Right End of Bail
C1633-40038 Bail Bracket - Located on Left End of Bail
C1633-40093 Encoder Strip Bracket - Installed on Left Side of Service Station
C1633-60029 Y-Drive Assembly Bracket - on Right Side of Plotter
C2847-00051 Y-Tensioner Bracket - Installed on Left Side Plate - (P/O the Bail Lift Mechanism Kit)
C3180-40013 Bracket for Bail Switch Assembly - Installed to the Right Side Plate of the Plotter

C1633-20034 Bushing for reduction pulley
C1633-40082 Bushing - Retains Spring on Shaft of Pincharm Assembly

Cable, Kabel
C2847-60005 Cable - from Power Supply to Main Logic Board
C2847-60019 Ribbon Cable - from Main Logic Bd to 'X' Encoder (on Motor)
C3180-60007 Trailing Cable - from Main Logic Board to Carriage Board

C1633-20012 Pincharm Bar Cam - Long Rod From Left to Right Side of Printer - Used to Lift the Pincharms
C1633-40052 Bail Lift Cam - Activates the Bail Lift Lever (P/O the Bail Lift Mechanism Kit)
C3180-40020 Pincharm Cam - Attached to Pincharm (Media) Lever
C3190-60149 Cam Jour l - Mounted on End of Pincharm Shaft (2 Used)

Carriage, Schlitten, Wagen
C1633-60120 Carriage Assembly - Includes Carriage PC Board

9170-1533 Clamp - Holds ferrite in place within electronics enclosure

Control Panel, Bedienfeld
C3180-60010 Control Panel - Mounts Behind Left Side of Front Panel Bezel

C1633-40003 Service Station Cover - Installed Directly Over the Service Station Cap
C3180-40003 Left end cover assembly - For end of upper stand (Chassis)
C3180-40004 Right end cover - For end of upper stand (Chassis) assembly
C3181-00003 Electronics enclosure - The larger of the two metal covers for the area containing the main PC board and power supply
C3181-00004 Electronics enclosure - The smaller of the two metal covers for the area containing the main PC board and power supply
C3181-00005 Cover - Top center of plotter
C3181-60008 Bottom cover

C3186-00034 Cross-brace - Main structure that extends between stand legs

C1633-00068 Door for tensioner housing
C3180-40015 Door - On right half of front panel bezel
C3180-40016 Help card lock - mounts to top of fold out front panel door

Fan, Lüfter
3160-0814 12V DC Fan - in Electronics Enclosure Assembly

Gear, Zahnrad
C1633-40019 Overdrive Gear Cluster - Mounts to the Left Side Plate of the Plotter Below the Clutch / Overdrive Gear Assembly
C1633-40027 Bail Engaging Lever Gear - Small Gear Mounted on the Support for the Bail Lift Cam Gear and the Bail Lift Engaging Gear (P/O the Bail Lift Mechanism Kit)
C1633-40028 Bail Lift Cam Gear - Large Gear Mounted on the Support for the Bail Lift Cam Gear and the Bail Lift Engaging Gear (P/O the Bail Lift Mechanism Kit) See Description Helical Drive Gear - Not Available Separately - Order the Motor/Gear

Gear Assembly
C4705-60089 Clutch / Overdrive Gear Assembly - Mounts Above the Cluster Gear on the Left Side Plate of the Plotter - Includes Gear, Clutch, Retaining Clip and Two Washers

C1633-00056 Trailing cable front guide (Tray)
C3181-40018 Media Guide - Mounted on Front of Overdrive Enclosure (2 Used)

Handle, Papier-Hebel
C3180-40017 Handle - Right side of plotter - Raise to load paper

0510-0083 Retaining E-Ring - Holds Overdrive Gear Assembly in Place
0570-1316 Hex Standoff - for RS-232C Connector (2 Used)

Hardware Kit
C2847-60061 Hardware kit - Package of 6 screws for stand assembly

C1633-40001 Service station housing - The base of the service station assembly
C1633-40065 Tensioner housing - Holds the tensioner wedge and tensioner spring for the carriage drive belt idler pulley
C3180-40012 Switch housing (mount) - For protecting the power switch

C3180-60013 Power supply insulator - Installed over power supply board

5041-1203 Power switch keycap (White)

Kit, Wartungs-Kit
5182-7322 Maintenance Kit - Includes Carriage Assembly, Wiper Pad, Left Bail Bracket, Reduction Pulley, 'Y' Belt and a Service Station Kit
C2847-60083 Service Station Kit - Includes Sled, Fitting Caps and Service Station Caps

C3195-00057 Safety Label - Provides Warning that Encoder Strip is Sharp Should be Placed so it is Visible when Top Cover is Open

C3180-40019 Latch assembly for top center cover

C2848-60002 Leg Assembly - Side Support with Foot Bar and 2 Casters (2 Used)

C2847-40013 Bail Engaging Lever - Used to Move Engaging Lever Gear (P/O the Bail Lift Mechanism Kit)

C1633-60033 Automatic cartridge adjust linkage

Memory (Product)
C2065A 4MB SIMM Memory Module Upgrade - 80nS, 36 Bit (One SIMM)
C2066A 8MB SIMM Memory Module Upgrade - 80nS, 36 Bit (One SIMM)

Memory (SIMM)
D2152-69001 8MB SIMM Memory Module - 80nS, 36 Bit (C2066A) REQUIRES RETURN OF DEFECTIVE PART(New part = D2152-63001)
D2156-69001 4MB SIMM Memory Module - 80nS, 36 Bit (C2065A) REQUIRES RETURN OF DEFECTIVE PART(New part = D2156-63001)
D2381-63001 2MB SIMM Memory Module - 80nS, 36 Bit (C2064A)

Module (Product)
J4101B Exter l JetDirect LAN Interface Module with EtherTwist (10Base-T/100Base-TX) Connector
J4102B Exter l JetDirect LAN interface module with EtherTwist (10Base-T) connector

C2847-60221 Motor Assy - 'Y' Axis Drive (Carriage) - with Power Cable
C3180-60005 Motor - Left Side of Plotter - Raises Cartridge Wiper Assy

C2848-60003 Motor/Encoder Assy (Includes Helical Drive Gear) - 'X' Axis Drive - NOTE: Motor and Gear are Only Sold as a Set

C1633-20006 'X' axis motor mount

C3187-00011  meplate - on Left Endcover

Overdrive/Bail Kit
C3191-60138 Overdrive and bail kit - Includes left and right bail brackets, 14 starwheel mount assemblies, bail lift mechanism kit, overdrive roller, overdrive enclosure, media guides

PC Board, Netzteil, Mainboard
0950-2417 Power supply board
C3180-69102 Main logic board REQUIRES RETURN OF DEFECTIVE PART(New part = C3180-60102) Carriage PC Board - NOT Sold Separately - Order Carriage Asy

C1633-60039 Pincharm Assembly - Curved Black Plastic Plate with 4 Small Rubber Rollers (Does NOT Include Spring or Bushing) (6 Used)

C3181-00002 Entry Platen - Large structure in front of platen roller

Power Module, Netzteil
0950-2372 Power supply module - 100-240VAC input, 47-63Hz, requires separate AC power cord - 5VDC output, 1A, 5 watts - For J2382/83A/B
0950-3170 Power supply module - 209-253VAC input, 47-53Hz - 13VDC output, 300mA - For Europe and Israel - For J2592A
0950-3349 Power Module - for JetDirect Modules and Infrared Interface Models J2590/91/93/94A, J2964A, J3258A/B, J3263/64/65A, J3282B, J4101A/B, J4102A/B - 230V in Europe/Israel

Pulley, Umlenkrolle
07570-60105 Idler Pulley - for Main Drive Belt - on Left End of Plotter
07570-60112 Idler Drive Pulley - Applies Tension to the Pen Carriage Drive Belt (Small Belt) - on Right End of Plotter
C3170-60009 Reduction Pulley - Between 'Y' Axis Belt and Carriage Belt

C3180-60006 AC power receptacle assembly - Includes cable

C2859-60004 Paper Drive (Platen) Roller Assy - Long Gear Driven Roller
C3191-60040 OverDrive Roller - Shaft W/Rollers - Runs Width of Plotter

C3180-60001 Media Sensor Assembly - under Right Side of Entry Platen
C3180-60009 Sensor - for Lift-up View Window - Right Side of Plotter
C3180-60034 Pincharm Sensor - on Right End of Chassis - Includes Cable

Sensor Mechanism
C3190-60130 Sensor Mechanism - the Mechanical Parts used with the Media Sensor - Does NOT Include the Media Sensor Assembly

C3193A Optio l Stand - Includes Legs, Casters, Brace and Wire Form Paper Defletor

Starwheel Mount
C4713-60035 Starwheel Mount Assembly (13 or 14 Used) - Includes Cover, Body, Spring, Two Starwheels - Mounts on the  Bail Assembly (Note: Part Number is for One Starwheel Mount Assembly ONLY)

Strip Encoder
C4714-60098 Encoder Strip Assembly - Connects from Left to Right Side of Plotter - Includes Encoder Strip and Encoder Strip Spring

C2847-40015 Cam Gear Support - Supports Bail Lift Cam Gear - Mounted on Y-Tensioner Bracket (P/O the Bail Lift Mechanism Kit)

Switch, Schalter
C3180-60002 Bail Switch Assembly - Installed on Right Side of Plotter

07550-40104 Tensioning Wedge - for the Pen Carriage Drive Belt Pulley - (Mounts on the Right Side of the Chassis)
07570-40105 Tensioning Wedge - for the Carriage Drive Belt Idler Pulley (Mounts on the Left Side of the Chassis)

C3181-60039 Lift-Up Viewing Window Assembly - on Top of Chassis

C1633-40006 Wiper Pad - Part of Wiper Assembly
C3180-60014 Wiper Assy - Left Side of Plotter - Part of Service Station - Includes Wiper Rocker, Wiper Rod and Wiper Pad

HP DesignJet 220 C3188A Ersatzteile


Hier finden Sie uns, Lageplan
Drucker Service Arfert und Loose GbR
Bahrenfelder Chaussee 101
22761 Hamburg

Tel: 040 / 57 50 35
Fax: 040 / 57 70 64
Montag bis Freitag von 8.00 bis 18.00 Uhr

Drucker Service Arfert und Loose GbR, Bahrenfelder Chaussee 101, 22761 Hamburg
© Copyright 1999 Arfert und Loose GbR. Alle Rechte vorbehalten

Drucker Service Arfert und Loose GbR

Tel: 040 / 57 50 35

Fax: 040 / 57 70 64

Drucker und HP DesignJet Plotter Dienstleistungen

Brother, Canon, Epson, Fujitsu, HP, Kyocera, Lexmark, Minolta, NEC, Oki, Philips, QMS, Samsung, Seikosha, Siemens, usw.