Bail
C3191-60095 Bail Assembly - Includes Bail, Starwheels, and Brackets

Bail Lift Mechanism
C2858-60209 Bail Lift Mechanism Kit - Includes Cam Gear, Engaging Lever, Engaging Lever Gear, Engaging Lever Spring, Y-Tensioner Bracket, Bail Lift Cam, Cam Gear Support, Screws, Washers

Belt, Zahnriemen, Antriebsriemen
1500-0855 'Y' Axis Belt - from Carriage Motor to Reduction Pulley
1500-0856 Carriage belt

Bin
C1633-00019 Media bin back - For top of wire rack below plotter
C1633-00020 Media Bin Front - Main Part of Wire Rack Below Plotter
C1633-00044 Media Bin Adjust - Adjustable Media Bottom Stop in Wire Rack

Bracket
07575-40125 Drive-Tensioner Bracket - Holds Pen Carriage Drive Belt Tensioning Wedge
C1633-00132 Encoder Spring Bracket - Installed on Right Side of Plotter
C1633-40037 Bail Bracket - Located on Right End of Bail
C1633-40038 Bail Bracket - Located on Left End of Bail
C1633-40093 Encoder Strip Bracket - Installed on Left Side of Service Station
C1633-60029 Y-Drive Assembly Bracket - on Right Side of Plotter
C2847-00051 Y-Tensioner Bracket - Installed on Left Side Plate - (P/O the Bail Lift Mechanism Kit)
C3180-40013 Bracket for Bail Switch Assembly - Installed to the Right Side Plate of the Plotter

Bushing
C1633-20034 Bushing for reduction pulley
C1633-40082 Bushing - Retains Spring on Shaft of Pincharm Assembly

Cable
C2847-60005 Cable - from Power Supply to Main Logic Board
C2847-60019 Ribbon Cable - from Main Logic Bd to 'X' Encoder (on Motor)
C3180-60007 Trailing Cable - from Main Logic Board to Carriage Board

Cam
C1633-20012 Pincharm Bar Cam - Long Rod From Left to Right Side of Printer - Used to Lift the Pincharms
C1633-40052 Bail Lift Cam - Activates the Bail Lift Lever (P/O the Bail Lift Mechanism Kit)
C3180-40020 Pincharm Cam - Attached to Pincharm (Media) Lever
C3190-60149 Cam Jour l - Mounted on End of Pincharm Shaft (2 Used)

Carriage, Carrier, Schlitten, Patronen-Wagen
C1633-60120 Carriage Assy - Includes Carriage PC Board - Can Be Used on any Plotter Regardless of Version of Firmware R
C2847-60071 Carriage Assy - Includes Carriage PC Board - Can be Used on Any Plotter That Has Firmware ROMS of Version A.01.01 or Higher - WARNING DAMAGE CAN OCCUR IF FIRMWARE VERSION IS NOT A.01.01 or Higher
Plotters with Serial Prefix ESA3700101 thru ESA4699999 May Need to Upgrade Firmware to Version A.01.01 or Higher and Install New Carriage if Having Print Problems

Control Panel. Bedienfeld
C3180-60010 Control Panel - Mounts Behind Left Side of Front Panel Bezel

Cover
C1633-40003 Service Station Cover - Installed Directly Over the Service Station Cap
C3180-40003 Left end cover assembly - For end of upper stand (Chassis)
C3180-40004 Right end cover - For end of upper stand (Chassis) assembly
C3181-00003 Electronics enclosure - The larger of the two metal covers for the area containing the main PC board and power supply
C3181-00004 Electronics enclosure - The smaller of the two metal covers for the area containing the main PC board and power supply
C3181-00005 Cover - Top center of plotter
C3181-60008 Bottom cover

Door
C1633-00068 Door for tensioner housing
C3180-40015 Door - On right half of front panel bezel
C3180-40016 Help card lock - mounts to top of fold out front panel door

Fan
3160-0814 12V DC Fan - in Electronics Enclosure Assembly

Gear, Zahnrad
C1633-40019 Overdrive Gear Cluster - Mounts to the Left Side Plate of the Plotter Below the Clutch / Overdrive Gear Assembly
C1633-40027 Bail Engaging Lever Gear - Small Gear Mounted on the Support for the Bail Lift Cam Gear and the Bail Lift Engaging Gear (P/O the

Bail Lift Mechanism Kit)
C1633-40028 Bail Lift Cam Gear - Large Gear Mounted on the Support for the Bail Lift Cam Gear and the Bail Lift Engaging Gear (P/O the Bail Lift Mechanism Kit) Helical Drive Gear - Not Available Separately - Order the Motor/Gear

Gear Assembly
C4705-60089 Clutch / Overdrive Gear Assembly - Mounts Above the Cluster Gear on the Left Side Plate of the Plotter - Includes Gear, Clutch, Retaining Clip and Two Washers

Guide
C1633-00056 Trailing cable front guide (Tray)
C3181-40018 Media Guide - Mounted on Front of Overdrive Enclosure (2 Used)

Handle, Papier-Hebel
C3180-40017 Handle - Right side of plotter - Raise to load paper

Hardware Kit
C2847-60061 Hardware kit - Package of 6 screws for stand assembly

Housing
C1633-40001 Service station housing - The base of the service station assembly
C1633-40065 Tensioner housing - Holds the tensioner wedge and tensioner spring for the carriage drive belt idler pulley
C3180-40012 Switch housing (mount) - For protecting the power switch

IC ROM
1818-6521 Masked ROM - U28 on MainBoard (Rev A.01.02) - NOTE: Replace EPROM's (40 Pin) U4, U9, U28, & U29 with New Masked ROM's (42 Pin) in U28/U29 Sockets and Leave U4/U9 Empty
1818-6522 Masked ROM - U29 on Main Logic Board (Rev A.01.02) - NOTE: Replace EPROM's (40 Pin) U4, U9, U28, & U29 with New Masked ROM's (42 Pin) in U28/U29 Sockets and Leave U4/U9 Empty

Keycap
5041-1203 Power switch keycap (White)

Kit, Wartungs Kit
5182-7322 Maintenance Kit - Includes Carriage Assembly, Wiper Pad, Left Bail Bracket, Reduction Pulley, 'Y' Belt and a Service Station Kit
C2847-60083 Service Station Kit - Includes Sled, Fitting Caps and Service Station Caps

Latch
C3180-40019 Latch assembly for top center cover

Leg
C2848-60002 Leg Assembly - Side Support with Foot Bar and 2 Casters (2 Used)

Lever
C2847-40013 Bail Engaging Lever - Used to Move Engaging Lever Gear (P/O the Bail Lift Mechanism Kit)

Motor
C2847-60221 Motor Assy - 'Y' Axis Drive (Carriage) - with Power Cable
C3180-60005 Motor - Left Side of Plotter - Raises Cartridge Wiper Assy

Motor/Gear
C2848-60003 Motor/Encoder Assy (Includes Helical Drive Gear) - 'X' Axis Drive - NOTE: Motor and Gear are Only Sold as a Set

Mount
C1633-20006 'X' axis motor mount

Overdrive/Bail Kit
C3191-60138 Overdrive and bail kit - Includes left and right bail brackets, 14 starwheel mount assemblies, bail lift mechanism
kit, overdrive roller, overdrive enclosure, media guides

PC Board, Netzteil, Mainboard
0950-2417 Power supply board
C3180-69102 Main logic board REQUIRES RETURN OF DEFECTIVE PART(New part = C3180-60102)

Pincharm
C1633-60039 Pincharm Assembly - Curved Black Plastic Plate with 4 Small Rubber Rollers (Does NOT Include Spring or Bushing) (6 Used)

Platen, Walzen
C3181-00002 Entry Platen - Large structure in front of platen roller

Power Module, Netzteil
0950-2372 Power supply module - 100-240VAC input, 47-63Hz, requires separate AC power cord - 5VDC output, 1A, 5 watts - For J2382/83A/B
0950-3170 Power supply module - 209-253VAC input, 47-53Hz - 13VDC output, 300mA - For Europe and Israel - For J2592A
0950-3349 Power Module - for JetDirect Modules and Infrared Interface Models J2590/91/93/94A, J2964A, J3258A/B, J3263/64/65A, J3282B, J4101A/B, J4102A/B - 230V in Europe/Israel

Pulley, Umlenkrolle
07570-60105 Idler Pulley - for Main Drive Belt - on Left End of Plotter
07570-60112 Idler Drive Pulley - Applies Tension to the Pen Carriage Drive Belt (Small Belt) - on Right End of Plotter
C3170-60009 Reduction Pulley - Between 'Y' Axis Belt and Carriage Belt

Receptacle
C3180-60006 AC power receptacle assembly - Includes cable

Roller
C2859-60004 Paper Drive (Platen) Roller Assy - Long Gear Driven Roller
C3191-60040 OverDrive Roller - Shaft W/Rollers - Runs Width of Plotter

Sensor
C3180-60001 Media Sensor Assembly - under Right Side of Entry Platen
C3180-60009 Sensor - for Lift-up View Window - Right Side of Plotter
C3180-60034 Pincharm Sensor - on Right End of Chassis - Includes Cable

Sensor Mechanism
C3190-60130 Sensor Mechanism - the Mechanical Parts used with the Media Sensor - Does NOT Include the Media Sensor Assembly

Stand
C3193A Optio l Stand - Includes Legs, Casters, Brace and Wire Form Paper Defletor

Starwheel Mount
C4713-60035 Starwheel Mount Assembly (13 or 14 Used) - Includes Cover, Body, Spring, Two Starwheels - Mounts on the
Bail Assembly (Note: Part Number is for One Starwheel Mount Assembly ONLY)

Strip Encoder
C4714-60098 Encoder Strip Assembly - Connects from Left to Right Side of Plotter - Includes Encoder Strip and Encoder Strip Spring

Support
C2847-40015 Cam Gear Support - Supports Bail Lift Cam Gear - Mounted on Y-Tensioner Bracket (P/O the Bail Lift Mechanism Kit)

Switch
C3180-60002 Bail Switch Assembly - Installed on Right Side of Plotter

Wedge
07550-40104 Tensioning Wedge - for the Pen Carriage Drive Belt Pulley - (Mounts on the Right Side of the Chassis)
07570-40105 Tensioning Wedge - for the Carriage Drive Belt Idler Pulley (Mounts on the Left Side of the Chassis)

Window
C3181-60039 Lift-Up Viewing Window Assembly - on Top of Chassis

Wiper
C1633-40006 Wiper Pad - Part of Wiper Assembly
C3180-60014 Wiper Assy - Left Side of Plotter - Part of Service Station - Includes Wiper Rocker, Wiper Rod and Wiper Pad

HP DesignJet 200 C3181A Ersatzteile

 

Hier finden Sie uns, Lageplan
Drucker Service Arfert und Loose GbR
Bahrenfelder Chaussee 101
22761 Hamburg
Mail: info@edvdrucker.de
Tel: 040 / 57 50 35
Fax: 040 / 57 70 64
Montag bis Freitag von 8.00 bis 18.00 Uhr

Drucker Service Arfert und Loose GbR, Bahrenfelder Chaussee 101, 22761 Hamburg
© Copyright 1999 Arfert und Loose GbR. Alle Rechte vorbehalten

Drucker Service Arfert und Loose GbR

Tel: 040 / 57 50 35

Fax: 040 / 57 70 64

Drucker und HP DesignJet Plotter Dienstleistungen

Brother, Canon, Epson, Fujitsu, HP, Kyocera, Lexmark, Minolta, NEC, Oki, Philips, QMS, Samsung, Seikosha, Siemens, usw.