Brother Laserdrucker Tintenstrahldrucker Fehlermeldungen Error Codes Fehler

Brother DCP8065, DCP 8060, MFC 8870, MFC 8460, MFC 8860

Error 56 = Fuser Klappe
Error 57 = Duplex Papierstau
Error 5A = HV Power
Error 5B = Toner Sensor oder Lever
Error 5C = Optionale Papierzuführung
Error 5D = Duplexeinheit fehlt
Error 60 = Papierablage voll oder Sensor def.
Error 68 = Fuser
Error 69 = Fuser
Error 6A = Fuser
Error 6B = Fuser
Error 6C = Fuser oder Netzteil
Error 6F = Fuser oder Netzteil
Error 6E = Fuser
Error 71 = Laser-Scanner
Error 72 = Laser-Scanner
Error 73 = Drum
Error 74 = Toner oder Toner Sensor

Brother DCP – MFC 8080, 8085, 8480, 8880, 8890 Error Codes

Error 1E = The drum unit reached its life and requires replacement.
Error 1F = Two or more optio l trays are installed
Error 24 = Inter l temperature sensor failure
Error 35 = EEPROM of main PCB failure
Error 36 = HVPS PCB during standby failure
Error 3B = Main PCB RAM failure
Error 3C = EEPROM writing error (Not applicable)
Error 3D = EEPROM reading error (Not applicable)
Error 3E = EEPROM bus error (Not applicable)
Error 44 = No toner cartridge
Error 50 = The drum unit reached its life and requires replacement.
Error 51 = The paper feed kit MP reached its life and requires replacement.
Error 52 = The paper feed kit T1 reached its life and requires replacement.
Error 53 = The paper feed kit T2 reached its life and requires replacement.
Error 54 = The fuser unit reached its life and requires replacement.
Error 55 = The laser unit reached its life and requires replacement.
Error 56 = Back cover is opened
Error 57 = Paper jam (Duplex tray)
Error 58 = Fuser unit failure
Error 59 = Fuser unit failure (Detect fuser failure at start-up)
Error 63 = Toner life end
Error 67 = Toner low
Error 68 = Temperature rise when heater is off
Error 69 = Mis-connect center thermistor connector
Error 6A = Fuser temperature does not reach 60°C within the specified time (center thermistor)
Error 6B = Fuser temperature does not reach 100°C within the specified time (center thermistor)
Error 6C = Fuser temperature exceeds its higher limit (center thermistor)
Error 6D = Fuser temperature exceeds its lower limit (center thermistor)
Error 6E = Fuser temperature does not rise (center thermistor)
Error 6F = Hardware detects extremely high temperature of the center or side thermistors
Error 70 = Fuser motor error
Error 71 = Laser unit polygon motor failure
Error 75 = Sensor of the inside temperature for detection detected higher than normal temperature
Error 76 = Rapid temperature rising failure (center thermistor)
Error 78 = Rapid temperature falling failure (center thermistor)
Error 7A = No detection of main motor synchronous sig l
Error 7D = Dirt on coro wire (detect discharge error)
Error 7F = Fax paper setting mismatch (The setting paper becomes besides the A4/Letter/Legal/Folio) (Not applicable)
Error 80= Fax paper size is incorrect (The paper is smaller 10mm than the letter size (11inch) in Fax List/Report)
Error 83 = Failure of discharge detection (Printing becomes u ble until the drum is replaced with a new one.)
(Discharge detection becomes u ble until the drum counter reaches the double of the drum life.)
Error 84 = Paper jam
Error 85 = Tray 1 is not installed into the machine
Error 86 = Tray 2 is not installed into the machine
Error 88 = Paper jam inside the machine
Error 89 = Incorrect paper size in duplex printing
Error 8A = Paper jam in Tray 1
Error 8B = Paper jam in Tray 2
Error 8C = Paper jam in MP Tray
Error 8D = Paper jam near eject tray
Error 99 = Specified paper size is not supported for duplex printing (Duplex)
Error 9F = Paper empty
Error A1 = Front cover opened
Error A2 = During scanning, 90 cm or longer of a document is detected
Error A3 = Document rear sensor is not turned on when feeding the document
Error A4 = ADF cover opened A5 Fax scanning error (Warning) (First time
Error A6 = Fax scanning error (Error) (Second time)
Error A7 = Scanning color parameter file failure
Error A8 = Scanning color parameter matching error
Error AD = DMA transfer error
Error AE = Document scanner home position sensor is not turned on.
Error AF = Document scanner home position sensor is not turned off.
Error B0 = Document scanner unit FFC detection error
Error B1 = Dark level offset data level error for scanning
Error B2 = Gain control data level error for scanning
Error B7 = A/D converter standard voltage failure; at High side
Error B8 = A/D converter standard voltage failure; at Low side
Error B9 = Scanning light adjustment error is detected
Error BB = White level data error
Error BD = Black level data error
Error BF = ADF duplex scanning cannot be implemented due to too long document
Error C0 = New toner detection lever failure
Error C7 = Insufficient DIMM Memory
Error C8 = Secure print data full
Error C9 = DIMM error
Error CA = Excess current to USB device that is front side of the machine
Error CD = Drum unit is not installed into the machine
Error D1 = Modem initialization failed
Error DD = Fuser error other than 58, 59, 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 76, 78, DE and E2 are occurred
Error DE = Central temperature of heat roller detected the temperature that was lower than 60°C)
Error E0 = Program error
Error E1 = Main PCB failure
Error E2 = Central temperature of heat roller exceeds 280°C
Error E6 = EEPROM error
Error EB = The data reading error for E2PROM
Error EC = Fuser fan failure
Error ED = Wireless LAN connection failure between W-LAN PCB and access point
Error EE = Wireless LAN is u ble to communicate between W-LAN PCB and access point
Error EF = LVPS PCB failure
Error F8 = Battery connection error
Error F9 = EEPROM customizing code error
Error FF = Excess current to USB HOST PCB error

Fehlermeldungen und Error Codes für Brother Laserdrucker

Hier finden Sie uns, Lageplan
Drucker Service Arfert und Loose GbR
Bahrenfelder Chaussee 101
22761 Hamburg
Mail: info@edvdrucker.de
Tel: 040 / 57 50 35
Fax: 040 / 57 70 64
Montag bis Freitag von 8.00 bis 18.00 Uhr

AGB