Memory (DIMM)
1818-8505 64MB, 133MHz, 3.3v, 144-pin SDRAM SO-DIMM memory module 
C7779-60269 64MB SO-DIMM memory module - Can be installed ONLY into the formatter board 
C7779-60270 128MB SO-DIMM memory module - Can be installed ONLY into the formatter board 

Memory (SIMM)
1818-5624 4MB, 70nS DRAM SIMM memory module 
D2297-69001 16MB, 70nS, 36-bit SIMM memory module 
D2298-69001 32MB, 70nS, 36-bit SIMM memory module Part D2298-69001 is no longer supplied. Please order the replacement, D3578-69001 
D2975-69001 8MB, 70nS, 36-bit parity SIMM memory module 
D3577-69001 8MB, 70nS, 36-bit parity SIMM memory module 
D3578-69001 32MB, 70nS, 36-bit parity SIMM memory module 
D3578A 32MB, 70nS, 36-bit parity SIMM memory module 

Memory Module
J2547-61001 Flash SIMM memory module - For upgrading older JetDirect EX Ethernet interface modules to the latest firmware revision - For automatic multiprotocol switching
Part J2547-61001 is no longer supplied. Please order the replacement, J3265-69001

PC Board (Interface)
J4167-69001 JetDirect 610N token ring LAN interface board - DB-9 and RJ-45 connectors 

Cable
C4713-60181 Carriage assembly trailing cable (D-size) - Has 60-pin (F) connectors - 1.6m (5.2ft) long 
C4713-60182 Flexible stranded wire cable - 12.5cm (4.9in) long 

Cable (Interface)
8121-0868 Universal Serial Bus (USB) interface cable (Black) - Type 'A' connector to type 'B' connector - 1.83m (6.0ft) long 

Cable Kit
C7769-60298 Ribbon cable kit - Includes installation instructions and ribbon cable with ferrite - Cable has 40 pin (F) connectors - 1.6m (5.1ft) long 
C7769-60305 Carriage assembly trailing cable kit - Includes installation instructions, trailing cables, two mounting clips, and a ferrite - Cables are 1.4m (4.7ft) long with 30 pin (M) edge connectors - For use with 24-inch plotters 

Belt
CH538-67018 Belt assembly - Includes belt tensioner - For 44-inch plotters 

Bushing
Q5669-60687 Carriage rear bushing 

Carriage
CH538-67044 Carriage with cutter Assembly - For the Designjet T770/T790/T1200/T1300/T2300 printer series Part CH538-67044 is no longer supplied. Please order the replacement, CR647-67025
 
Cover
CK837-67002 Carriage cover - For the Designjet printers 
CK837-67003 Carriage PCA covers - For Designjet printers Part CK837-67003 is no longer supplied. Please order the replacement, CK837-67028
 
Cutter
CN727-67023 Cutter assembly - Includes screw 

Ink Tubes Assembly
CH538-67025 Ink supply tubes - Includes trailing cable - For use with Designjet printers Part CH538-67025 is no longer supplied. Please order the replacement, CR649-67004
 
Latch
CK837-67001 Carriage latch - For the Designjet printers 

PC Board
CK837-67005 Carriage PCA - Controls movement of carriage assembly - For Designjet printers 

Sensor
Q6683-67004 Line sensor - Detects paper width and skew - Measures calibration accuracy and printhead alignment Part Q6683-67004 is no longer supplied. Please order the replacement, CR647-67024
 
Strip
CK839-67005 Encoder strip - Includes the encoder strip spring and nut - For Designjet printers 

Cover
CH538-67012 Back cover - For the Designjet T1200/T770 printer series 
CH538-67013 Left cover assembly - Includes the ink door - For the Designjet T1200 printer series 
CH538-67014 Right cover - For the Designjet T1200 printer series 
CH538-67026 Top cover - For the 44-inch Designjet T1200 printer series 
CH539-67005 Left cover assembly - Includes the ink door - For the Designjet T770 printer series 
CH539-67006 Right cover - For the Designjet T770 printer series 
CH539-67011 Top cover - For the 44-inch Designjet T770 printer series 
Q6687-60064 Front cover assembly - For 44-inch plotters 

Door
CH538-67017 Left ink cartridge door - For Designjet printers 
CH538-67045 Right ink cartridge door - For the Designjet T1200/T770 printer series 
CH539-67008 Left ink cartridge door - For the Designjet T770 printer series 

Front Panel
CH538-67032 Front panel - For the 44-inch Designjet T1200 printer series 

Hardware
CH538-67022 Converger assembly - For the 44-inch Designjet printers 
CH539-67010 Converger CR assembly - For the Designjet T770 printer series 

Panel
CH538-67005 Left side panel - For Designjet printers 
CH539-67002 Left side panel - For 24-inch plotters 

Paper Path Module
CH538-67039 Clean out - For the 44-inch Designjet T1200/T770 printer series 

Platen
Q6659-60089 Output platen assembly - For 44-inch plotters 

Sensor
CH538-67071 Window position sensor - Includes shield 
Q5669-67068 Out of paper sensor (OOPS) 

Trim
Q6675-60109 Left and right trim assemblies 

Window
CH538-67030 Front panel window cover - For 44-inch plotters 

Belt
C4705-60082 Carriage belt (D-size) - Long/wide belt attached to the carriage 
C7769-60182 Carriage belt - Drives the carriage assembly - For use with 24-inch plotters 
C7769-60392 Carriage belt (24-inch)
 
Bushing
C7769-60169 Cutter bushing 

Cam
C2847-20005 Pinch arm bar cam (D-size) - Long rod from left to right side of printer - Used to lift the pinch arms 
C3190-40020 Bail lift cam - Mounted behind the bail engaging lever support 

Clutch
C4713-60129 Overdrive clutch assembly - Small, wide gear near overdrive gear - Held in place with a retaining E-ring 

Encoder
C7769-60254 Encoder disk assembly - Helps provide position the information of the paper 

End Cap
C3174-40011 Spindle end cap (2-inch) 

Fan
C7769-60407 Vacuum fan assembly 

Gear
C1633-40027 Bail engaging lever gear 
C3190-40019 Bail lift cam gear
 
Gear Assembly
C7769-60177 Paper drive transmission gear kit - Includes two gears used to drive the paper drive roller Part C7769-60177 is no longer supplied. Please order the replacement, C7769-60408
C7769-60408 Paper drive transmission gear kit - Includes two gears used to drive the paper drive roller 

Guide
C4713-60184 Rollfeed guide kit - Left and right guides mounted under printer - Used to attach rollfeed housings to the printer 
C7769-60179 Cutter guide - Guide bar for the cutter assembly - For 24-inch plotters 

Motor
C4713-60092 Carriage motor assembly - Includes cable 
C7769-60375 Carriage (scan-axis) motor assembly - Includes cable 
C7769-60377 Paper axis motor assembly - Includes cables 

Platen
C4713-60114 Entry platen assembly (D-size) - Curved cover/guide that is next to the paper drive (platen) roller 
C7769-60155 Back platen assembly - Curved cover/guide that is installed below the paper drive roller (24-inches) Part C7769-60155 is no longer supplied. Please order the replacement, C7769-60410
C7769-60174 Front platen kit - Includes platens for both the 24-inch and the 42-inch models 
C7769-60410 Back platen assembly - Curved cover/guide that is installed below the paper drive roller - For use with 24-inch plotters 
Q5669-60155 Output platen assembly - For 24-inch plotters 

Sensor
C4713-60034 Pincharm sensor assembly 
C7769-60168 Media sensor Part C7769-60168 is no longer supplied. Please order the replacement, C7769-60379
C7769-60194 Pincharm sensor Part C7769-60194 is no longer supplied. Please order the replacement, C7769-60378
C7769-60378 Pincharm sensor - Installed in right front of print chassis 
C7769-60379 Media sensor - Installed in the front of the rear platen 
C7769-60384 Drive roller encoder sensor 

Spring
07575-80012 Bail gear support 'claw' spring - Attached between the bail engaging lever support and the bail gear assembly 
C4699-00016 Encoder spring 
C4713-80003 Pincharm spring 

Carriage
Q6675-60043 Carriage rail oiler 

Drive
CH538-67078 SATA Hard Disk Drive (HDD) - Includes firmware - For use with Designjet printers 

Encoder
CH538-67073 Encoder disk - Helps provide position the information of the paper 

Ink Supply Station
Q6683-60188 Left ink supply station - For the Designjet printers 

Motor
CH538-67027 Media motor - For Designjet printers 
CH538-67076 Scan-axis motor - For use with Designjet printers 
Q6718-67017 Starwheel motor assembly - For Designjet priners 

PC Board
CH538-67004 Formatter board - Does NOT include the Hard Disk Drive (HDD) - For the Designjet T1200 printer series 
CH538-67009 Main PCA - Includes Power Supply Unit (PSU) 

Pinch Assembly
Q5669-60705 Pinch lift assembly - Molded plastic part - Guides the paper during paper advancement 

Power Supply
CH538-67011 Power Supply Unit (PSU) - For the Designjet T1200/T770 printer series Part CH538-67011 is no longer supplied. Please order the replacement, CR647-67010
 
Sensor
CK837-67020 Encoder sensor assembly - For Designjet printers Part CK837-67020 is no longer supplied. Please order the replacement, CR647-67023
Q5669-60666 Drop detector sensor assembly 
Q5669-60706 Pinchwheel lifter sensor

Service Station
CH538-67040 Service station - Includes the drop detector and the service station spittoon - For the Designjet T1200/T770 printer series 
Q5669-60667 Spittoon service station - For Designjet printers 

Solenoid
Q5669-67807 Pen to paper space (PPS) solenoid - For Designjet printers 

Spittoon
Q5669-67049 Left-side spittoon assembly - Holds expelled ink from cartridge during refresh cycle 

Logic/Control Electronics
5188-6700 Universal AC power adapter - Separate AC power adapter with attached DC power cord - Requires country-specific AC power cord with C7 connector - 100-240VAC, 50/60Hz input, 12VDC, 1.25A output 

Module
C4713-69203 Electronics module - Contains power supply, main logic board, interface connectors, and fan 
C7779-60144 Electronics module - Contains main logic board, connectors for plug-in cards, connector for parallel interface cable, connector for USB cable, and cooling fan 
C7779-60263 Electronics module - Contains main logic board, connectors for plug-in cards, connector for parallel interface cable, connector for USB cable, and cooling fan 
C7779-69263 Electronics module - Contains main logic board, connectors for plug-in cards, connector for parallel interface cable, connector for USB cable, and cooling fan 

PC Board
C7769-60385 Interconnect PC board - Installed in right-side of printer 
C7769-60441 HP-GL/2 and RTL formatter PC board 
C7769-69441 HP-GL/2 and RTL formatter PC board 

Power Supply
C7769-60387 Power supply assembly - Includes power switch 
CH336-67012 Power supply assembly - For the Designjet 510 printer series Part CH336-67012 is no longer supplied. Please order the replacement, CH336-67014
 
Cable
CK837-67008 Left and right side harness cables - For Designjet printers 

Cable Kit
CH538-67006 Cable kit - For the Designjet T series printers 
CH539-67003 Cable kit - For the Designjet T770 printer series 

Ink System Kit
Q6675-67004 Ink system purgers - Includes six units 
Q6675-67005 Ink system purgers - Includes 100 units 

Maintenance Kit
CH538-67024 Preventive maintenance kit 1 - Includes the carriage with cutter assembly, scan-axis motor, tube system with trailing cable, and belt - For the 44-inch Designjet T series printers Part CH538-67024 is no longer supplied. Please order the replacement, CR649-67003
 
Paper Path Module
Q6687-60093 Paper advance calibration kit - For 44-inch plotters 

Tool
Q5669-60690 Flex contacts cleaning tool 
Q6675-67017 Spanner tool 
Q6675-67018 Media driver tool kit - Includes the handle for media driver tool support and the media driver adjustment tool 
Q6683-67001 Tool kit - Includes pincwheel alignment tool, media driver tool, spanner number 13, oil dispenser, insert spring tool, tweezers, T15 screwdriver, 100cc isopropyl alcohol, lubricant oil, plastic gloves, flex contacts cleaning tool, and cleaning kit Part Q6683-67001 is no longer supplied. Please order the replacement, Q6683-67028
Q6687-60084 Pinchwheel insertion tool - For Designjet printers 

Actuator
CH538-67064 Left and right side bumper cutter actuator - For the Designjet T series printers
 
Foam
Q6659-60182 Full bleed foam kit - For 44-inch plotters 

Guide
Q6675-60044 Right side roll guide assembly Part Q6675-60044 is no longer supplied. Please order the replacement, Q6675-67026
Q6677-60019 Left side roll guide assembly - For 44-inch plotters 

Lifter
Q5669-67054 Starwheel lifter assembly - For Designjet printers 

Overdrive Assembly
Q6677-60018 Print zone overdrive assembly - For 44-inch plotters 

Pinchwheel
Q6687-60085 Pinchwheel assembly - For the Designjet T series printers 

Spindle
Q6687-67001 44-inch spindle assembly 

Starwheel
CK839-67009 Starwheel assembly - For 44-inch plotters 

Power Module/Recharger
0950-3358 Power module (Wall mount, MEI-AH ED12063) - Input voltage 240VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Australia and New Zealand) 
0957-2340 Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts
5188-5676 Power module (wall mount) - Input voltage 100VAC, 47/63Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Japan) 

Ink Tubes Assembly
C7769-60381 Ink tubes assembly - Includes 4 ink tubes complete with hardware assemblies at both ends (carriage crane and ink supply station crane), and 4 setup pens - For the 24-inch Designjet 500/800 printer series 

Printhead
C7769-60164 Setup printhead kit - Used to prime the ink tubes - Includes 4 setup printheads 
C9380A HP 72 Gray and Photo Black Printhead 
C9383A HP 72 Magenta and Cyan Printhead 
C9384A HP 72 Matte Black and Yellow Printhead 

Bumper
CH538-67051 Left and right side upper roll support bumpers - For the Designjet T series printers 
CH538-67052 Left and right side lower roll support bumpers - For the Designjet T series printers
 
Cover
CH538-67002 Lower roll cover assembly - With pinches - For Designjet printers 
CH538-67003 Upper roll cover assembly - Includes pinches - For Designjet printers 
CH538-67047 Roll cover bi-stable springs left and right - For Designjet printers 
CH538-67050 Roll cover freewheel assembly - For Designjet printers 
CH539-67009 Basic upper roll cover assembly - For the Designjet T770 printer series
 
Pincharm
CH538-67037 Pincharm assembly for roll cover - For the Designjet T1200 printer series 

Sensor
CH538-67033 Single sheet sensor - For the Designjet T series printers 
CH538-67041 Lower left support sensor with cable - For the Designjet T series printers 

Spacer
CH538-67046 Left and right side wall spacers - For the Designjet T series printers 

Support
CH538-67015 Upper left support - For the Designjet T1200/T770 printer series 
CH538-67016 Lower left side support - For the Designjet T1200 printer series 
CH538-67028 Upper right support - For the Designjet T1200/T770 printer series 
CH538-67029 Lower right side support - For the Designjet T1200 printer series 
CH538-67065 Upper left support sensor with cable - For the Designjet T series printers 
CH539-67007 Upper left support - Without sensor - For the Designjet T770 printer series 

Bin
CH639-69002 Media bin (Black) - Includes bin and support - Mounts to the printer stand legs 
Q6659-60237 Media bin (Gray) - Includes bin and support - Mounts to the printer stand legs - For 44-inch plotters
 
Bracket
Q6712-69001 Foot bracket (Gray) - Includes two units Part Q6712-69001 is no longer supplied. Please order the replacement, CH539-69001
 
Cover
Q5669-60718 Leg cover - Slides down outside of stand legs 

Cross-Brace
Q6659-60236 Cross-brace - Connects and supports the two stand legs - For 44-inch plotters
 
Foot
CH639-69001 Foot assembly (Black) - Includes two feet Part CH639-69001 is no longer supplied. Please order the replacement, CH539-69001
 
Hardware Kit
Q5669-60730 Hardware kit for printer stand - Includes screwdriver and screws - Used to assemble printer stand
 
Leg
Q5669-60716 Leg assembly - Side support for the plotter - Does NOT include the foot assembly

HP DesignJet T1200 CK834A Plotter Ersatzteil - Liste

 

Hier finden Sie uns, Lageplan
Drucker Service Arfert und Loose GbR
Bahrenfelder Chaussee 101
22761 Hamburg

Mail: info@edvdrucker.de
Tel: 040 / 57 50 35
Fax: 040 / 57 70 64
Montag bis Freitag von 8.00 bis 18.00 Uhr

Drucker Service Arfert und Loose GbR, Bahrenfelder Chaussee 101, 22761 Hamburg
© Copyright 1999 Arfert und Loose GbR. Alle Rechte vorbehalten

Drucker Service Arfert und Loose GbR

Tel: 040 / 57 50 35

Fax: 040 / 57 70 64

Drucker und HP DesignJet Plotter Dienstleistungen

Brother, Canon, Epson, Fujitsu, HP, Kyocera, Lexmark, Minolta, NEC, Oki, Philips, QMS, Samsung, Seikosha, Siemens, usw.